Incorporation by reference.

§ 2.910 Incorporation by reference. (a) The materials listed in this section are incorporated by reference in this part. These incorporations by reference were approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval, and notice of any change in these materials will be published in the Federal Register. All approved material is available for inspection at the Federal Communications Commission, located at the address indicated in 47 CFR 0.401(a), Tel: (202) 418-0270, and is available from the sources listed in this section. It is also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (b) International Electrotechnical Commission (IEC), IEC Central Office, 3, rue de Varembe, CH-1211 Geneva 20, Switzerland, Email: inmail@iec.ch, www.iec.ch. (1) CISPR 16-1-4:2010-04: “Specification for radio disturbance and immunity measuring apparatus and methods—Part 1-4: Radio disturbance and immunity measuring apparatus—Antennas and test sites for radiated disturbance measurements”, Edition 3.0, 2010-04, IBR approved for §§ 2.948(d) and 2.950(f). (2) [Reserved] (c) Institute of Electrical and Electronic Engineers (IEEE), 3916 Ranchero Drive, Ann Arbor, MI 48108, 1-800-699-9277, http://www.techstreet.com/ieee; (IEEE publications can also be purchased from the American National Standards Institute (ANSI) through its NSSN operation ( www.nssn.org ), at Customer Service, American National Standards Institute, 25 West 43rd Street, New York, NY 10036, telephone (212) 642-4900.) (1) ANSI C63.4-2014: “American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz,” ANSI approved June 13, 2014, IBR approved for § 2.950(h) and: (i) Sections 5.4.4 through 5.5, IBR approved for §§ 2.948(d) and 2.950(f); (ii) [Reserved] (2) ANSI C63.10-2013, “American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices,” ANSI approved June 27, 2013, IBR approved for § 2.950(g). (3) ANSI C63.26-2015, “American National Standard of Procedures for Compliance Testing of Transmitters Used in Licensed Radio Services,” ANSI approved December 11, 2015, IBR approved for § 2.1041(b). (d) International Organization for Standardization (ISO), 1, ch. De la Voie-Creuse, CP 56, CH-1211, Geneva 20, Switzerland; www.iso.org ; Tel.: + 41 22 749 01 11; Fax: + 41 22 733 34 30; email: central@iso.org . (ISO publications can also be purchased from the American National Standards Institute (ANSI) through its NSSN operation ( www.nssn.org ), at Customer Service, American National Standards Institute, 25 West 43rd Street, New York, NY 10036, telephone (212) 642-4900.) (1) ISO/IEC 17011:2004(E), “Conformity assessment—General requirements for accreditation bodies accrediting conformity assessment bodies,” First Edition, 2004-09-01, IBR approved for §§ 2.948(e), 2.949(b), 2.950(c) and (d), and 2.960(c). (2) ISO/IEC 17025:2005(E), “General requirements for the competence of testing and calibration laboratories,” Section Edition, 2005-05-15, IBR approved for §§ 2.948(e), 2.949(b), 2.962(c) and (d). (3) ISO/IEC 17065:2012(E), “Conformity assessment—Requirements for bodies certifying products, processes and services,” First Edition, 2012-09-15, IBR approved for §§ 2.950(b), 2.960(b), 2.962(b), (c), (d), (f), and (g). (4) ISO/IEC Guide 58:1993(E), “Calibration and testing laboratory accreditation systems—General requirements for operation and recognition”, First Edition 1993, IBR approved for § 2.950(d). (5) ISO/IEC Guide 61:1996(E), “General requirements for assessment and accreditation of certification/registration bodies”, First Edition 1996, IBR approved for § 2.950(c). (6) ISO/IEC Guide 65:1996(E), “General requirements for bodies operating product certification systems,” First Edition 1996, IBR approved for § 2.950(b). [80 FR 33439, June 12, 2015, as amended at 82 FR 50826, Nov. 2, 2017; 85 FR 64406, Oct. 13, 2020] § 2.910, Nt. Effective Date Note: At 88 FR 67114, Sept. 29, 2023, § 2.910 was revised, effective Oct. 30, 2023. For the convenience of the user, the revised text is set forth as follows: § 2.910 Incorporation by reference. Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, the Federal Communications Commission (FCC) must publish a document in the Federal Register and the material must be available to the public. All approved incorporation by reference (IBR) material is available for inspection at the FCC and at the National Archives and Records Administration (NARA). Contact the FCC at the address indicated in 47 CFR 0.401(a), phone: (202) 418-0270. For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations.html or email fr.inspection@nara.gov. The material may be obtained from the following source(s): (a) International Electrotechnical Commission (IEC), IEC Central Office, 3, rue de Varembe, CH-1211 Geneva 20, Switzerland; email: inmail@iec.ch; website: www.iec.ch. (1) CISPR 16-1-4:2010-04, Specification for radio disturbance and immunity measuring apparatus and methods—Part 1-4: Radio disturbance and immunity measuring apparatus—Antennas and test sites for radiated disturbance measurements, Edition 3.0, 2010-04; IBR approved for § 2.948(d). (2) [Reserved] (b) Institute of Electrical and Electronic Engineers (IEEE), 3916 Ranchero Drive, Ann Arbor, MI 48108; phone: (800) 678-4333; email: stds-info@ieee.org; website: www.ieee.org/. (1) ANSI C63.4-2014, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz, ANSI-approved June 13, 2014, Sections 5.4.4 (“Radiated emission test facilities—Site validation”) through 5.5 (“Radiated emission test facilities for frequencies above 1 GHz (1 GHz to 40 GHz)”), copyright 2014; IBR approved for § 2.948(d). (2) ANSI C63.4a-2017, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz, Amendment 1: Test Site Validation, ANSI-approved September 15, 2017; IBR approved for § 2.948(d). (3) ANSI C63.25.1-2018, American National Standard Validation Methods for Radiated Emission Test Sites, 1 GHz to 18 GHz, ANSI-approved December 17, 2018; IBR approved for § 2.948(d). (4) ANSI C63.26-2015, American National Standard of Procedures for Compliance Testing of Transmitters Used in Licensed Radio Services, ANSI-approved December 11, 2015; IBR approved for § 2.1041(b). (c) International Organization for Standardization (ISO), Ch. de Blandonnet 8, CP 401, CH-1214 Vernier, Geneva, Switzerland; phone: + 41 22 749 01 11; fax: + 41 22 749 09 47; email: central@iso.org; website: www.iso.org. (1) ISO/IEC 17011:2004(E), Conformity assessment—General requirements for accreditation bodies accrediting conformity assessment bodies, First Edition, 2004-09-01; IBR approved for §§ 2.948(e); 2.949(b); 2.960(c). (2) ISO/IEC 17025:2005(E), General requirements for the competence of testing and calibration laboratories, Second Edition, 2005-05-15; IBR approved for §§ 2.948(e); 2.949(b); 2.950(a); 2.962(c) and (d). (3) ISO/IEC 17025:2017(E), General requirements for the competence of testing and calibration laboratories, Third Edition, November 2017; IBR approved for §§ 2.948(e); 2.949(b); 2.950(a); 2.962(c) and (d). (4) ISO/IEC 17065:2012(E), Conformity assessment—Requirements for bodies certifying products, processes and services, First Edition, 2012-09-15; IBR approved for §§ 2.960(b); 2.962(b), (c), (d), (f), and (g). Note 1 to § 2.910: The standards listed in paragraphs (b) and (c) of this section are also available from the American National Standards Institute (ANSI), 25 West 43rd Street, 4th Floor, New York, NY 10036; phone (212) 642-4980; email info@ansi.org; website: https://webstore.ansi.org/. Application Procedures for Equipment Authorizations